Skip to main content

HomeProblems

Dishwasher Not Filling With Water? 6 Causes Ranked by Likelihood (With Tests)

Symptoms:

Dishwasher Not Filling With Water? 6 Causes Ranked by Likelihood (With Tests)

No water reaching the tub almost always traces back to a closed supply valve or a float switch stuck in the full position, rarely a failed inlet valve.

Risk
Low
Difficulty
Intermediate
Estimated time
15 to 30 minutes

Before you start

Unplug the appliance, shut off the water supply if relevant, and stop immediately if you smell burning. If in doubt, call a qualified professional.

On this page

Open the door mid-cycle and the tub is bone dry: the dishwasher either isn’t getting water at all, or it thinks it already has enough. Both point away from the pump and toward the water supply side of the machine.

Part of our full dishwasher troubleshooting guide. If water is arriving but not draining back out, see dishwasher not draining instead.

Quick Diagnosis Table

CauseLikelihoodDifficultyTypical Cost
Water supply valve closed or partly closedVery likelyEasy$0
Kinked or blocked fill hoseLikelyEasy$0
Float switch stuck in the up positionLikelyEasy$0
Clogged inlet valve screenPossibleModerate$0–20
Faulty water inlet valvePossibleModerate$25–60
Control board not triggering the fillRareProfessional recommended$150–300+

Repair or Replace?

Every likely cause here is free to fix or under $20 in parts. Even a full inlet valve replacement is a modest, DIY-friendly repair on most models, so there’s little reason to think about replacing the dishwasher over this symptom alone.

Inlet valve location and float switch design differ across Whirlpool, GE, Samsung, LG, Bosch, KitchenAid, Frigidaire, and Maytag. Brand-specific access guides are on the way.

Frequently Asked Questions

I hear a humming or clicking sound but no water comes in, what does that mean?

That's consistent with a stuck or failing inlet valve rather than a closed supply, since the dishwasher is actively trying to open the valve.

Could the float switch be the issue even if the tub looks empty?

Yes. If the float itself is stuck in the raised position, often from trapped debris, the dishwasher reads it as already full and skips the fill entirely.

Is this the same as a dishwasher that fills then immediately drains?

No, that's typically a drain hose installed too low or a missing high-loop, a plumbing issue rather than a fill problem.

Do I need to turn off the water supply before checking the inlet valve?

Yes, always shut the valve under the sink and unplug the dishwasher before opening any water-carrying component.

The information provided here is a diagnostic aid and does not replace the intervention of a qualified professional.

Tools needed

Probable causes

First checks

Step-by-step diagnosis

  1. Open the water supply valve under the sink fully and confirm water flows to the connection.
  2. Straighten any kinked section of the fill hose and check both connections are firm.
  3. Remove debris from around the float switch and confirm it rises and falls freely.
  4. Unplug the dishwasher, shut the water supply, and clean the small mesh screen at the inlet valve's inlet port.
  5. Test the inlet valve's solenoid coil resistance with a multimeter per your model's spec, replace if it reads open or shorted.
  6. If the valve and float both test fine, the control board may not be sending the fill signal, and that calls for a technician.

Mistakes to avoid

When to stop

Parts potentially involved

When to call a professional

If the simple checks didn’t solve it, if the fix involves electrical wiring, gas, or the refrigerant circuit, or if you have any doubt at all: stop there and hand the appliance to a qualified repair professional.

Related guides

Error codes for this appliance

The information provided here is a diagnostic aid and does not replace the intervention of a qualified professional.

Sam Radford — DiagnosFix

Sam Radford — DiagnosFix

Technical reviewer

Last verified: 2026-07-19